Turning Up the Heat on Thermoelectrics
May 29, 2018 | MITEstimated reading time: 6 minutes
Imagine being able to power your car partly from the heat that its engine gives off. Or what if you could get a portion of your home’s electricity from the heat that a power plant emits? Such energy-efficient scenarios may one day be possible with improvements in thermoelectric materials — which spontaneously produce electricity when one side of the material is heated.
Over the last 60 years or so, scientists have studied a number of materials to characterize their thermoelectric potential, or the efficiency with which they convert heat to power. But to date, most of these materials have yielded efficiencies that are too low for any widespread practical use.
MIT physicists have now found a way to significantly boost thermoelectricity’s potential, with a theoretical method that they report today in Science Advances. The material they model with this method is five times more efficient, and could potentially generate twice the amount of energy, as the best thermoelectric materials that exist today.
“If everything works out to our wildest dreams, then suddenly, a lot of things that right now are too inefficient to do will become more efficient,” says lead author Brian Skinner, a postdoc in MIT’s Research Laboratory of Electronics. “You might see in people’s cars little thermoelectric recoverers that take that waste heat your car engine is putting off, and use it to recharge the battery. Or these devices may be put around power plants so that heat that was formerly wasted by your nuclear reactor or coal power plant now gets recovered and put into the electric grid.”
Skinner’s co-author on the paper is Liang Fu, the Sarah W. Biedenharn Career Development Associate Professor of Physics at MIT.
Finding holes in a theory
A material’s ability to produce energy from heat is based on the behavior of its electrons in the presence of a temperature difference. When one side of a thermoelectric material is heated, it can energize electrons to leap away from the hot side and accumulate on the cold side. The resulting buildup of electrons can create a measurable voltage.
Materials that have so far been explored have generated very little thermoelectric power, in part because electrons are relatively difficult to thermally energize. In most materials, electrons exist in specific bands, or energy ranges. Each band is separated by a gap — a small range of energies in which electrons cannot exist. Energizing electrons enough to cross a band gap and physically migrate across a material has been extremely challenging.
Skinner and Fu decided to look at the thermoelectric potential of a family of materials known as topological semimetals. In contrast to most other solid materials such as semiconductors and insulators, topological semimetals are unique in that they have zero band gaps — an energy configuration that enables electrons to easily jump to higher energy bands when heated.
Scientists had assumed that topological semimetals, a relatively new type of material that is largely synthesized in the lab, would not generate much thermoelectric power. When the material is heated on one side, electrons are energized, and do accumulate on the other end. But as these negatively charged electrons jump to higher energy bands, they leave behind what’s known as “holes” — particles of positive charge that also pile up on the material’s cold side, canceling out the electrons’ effect and producing very little energy in the end.
But the team wasn’t quite ready to discount this material. In an unrelated bit of research, Skinner had noticed a curious effect in semiconductors that are exposed to a strong magnetic field. Under such conditions, the magnetic field can affect the motion of electrons, bending their trajectory. Skinner and Fu wondered: What kind of effect might a magnetic field have in topological semimetals?
They consulted the literature and found that a team from Princeton University, in attempting to fully characterize a type of topological material known as lead tin selenide, had also measured its thermoelectric properties under a magnetic field in 2013. Among their many observations of the material, the researchers had reported seeing an increase in thermoelectric generation, under a very high magnetic field of 35 tesla (most MRI machines, for comparison, operate around 2 to 3 tesla).
Skinner and Fu used properties of the material from the Princeton study to theoretically model the material’s thermoelectric performance under a range of temperature and magnetic field conditions.
“We eventually figured out that under a strong magnetic field, a funny thing happens, where you could make electrons and holes move in opposite directions,” Skinner says. “Electrons go toward the cold side, and holes toward the hot side. They work together and, in principle, you could get a bigger and bigger voltage out of the same material just by making the magnetic field stronger.”
Page 1 of 2
Suggested Items
The Shaughnessy Report: Unlock Your High-speed Material Constraints
05/15/2024 | Andy Shaughnessy -- Column: The Shaughnessy ReportThe world of PCB materials used to be a fairly simple one. It was divided into two groups: the “traditional” laminates, often called FR-4, and the high-speed laminates developed especially for high-speed PCBs. These were two worlds that usually didn’t collide. But then traditional laminates started getting better, and high-speed designers and design engineers took notice and started to reconsider what FR-4 could be used for.
Breaking High-speed Material Constraints: Design007 Magazine — May 2024
05/14/2024 | I-Connect007 Editorial TeamDo you need specialty materials for your high-speed designs? Maybe not. Improvements in resins mean designers of high-speed boards can sometimes use traditional laminate systems instead of high-speed materials, saving time and money while streamlining the fab process. In the May 2024 issue of Design007 Magazine, our contributors explain how to avoid overconstraining your materials when working with high-speed boards.
Indium Experts to Present at Electronics in Harsh Environments SMTA Conference
05/13/2024 | Indium Corporationndium Corporation Technical Manager for Europe, Africa, and the Middle East, Karthik Vijay, will deliver a technical presentation and Indium Corporation Senior Technologist, Dr. Ronald Lasky, will deliver both a workshop and technical presentation at the Electronics in Harsh Environments SMTA Conference on May 14-16 in Copenhagen, Denmark.
Ansys’ Collaboration with Schrödinger will Accelerate Materials Development with Unprecedented Multiscale Simulation
05/09/2024 | ANSYSAnsys and Schrödinger are collaborating to deliver an ICME approach that bridges the gap between materials discovery and product development.
2024 Apple iPad Pro Estimated to Ship Between 4.5 to 5 Million Units
05/08/2024 | TrendForceApple’s recent product launch in May introduced a lineup of new tablets featuring advanced AMOLED screens. Notably, the Pro version boasts a dual-layer tandem structure designed to address the longstanding challenges of screen burn-in and lifespan that are common with AMOLED displays.