-
- News
- Books
Featured Books
- smt007 Magazine
Latest Issues
Current IssueIPC APEX EXPO 2024 Pre-show
This month’s issue devotes its pages to a comprehensive preview of the IPC APEX EXPO 2024 event. Whether your role is technical or business, if you're new-to-the-industry or seasoned veteran, you'll find value throughout this program.
Boost Your Sales
Every part of your business can be evaluated as a process, including your sales funnel. Optimizing your selling process requires a coordinated effort between marketing and sales. In this issue, industry experts in marketing and sales offer their best advice on how to boost your sales efforts.
The Cost of Rework
In this issue, we investigate rework's current state of the art. What are the root causes and how are they resolved? What is the financial impact of rework, and is it possible to eliminate it entirely without sacrificing your yields?
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - smt007 Magazine
Tips & Tricks: Water Contamination and Flux Expiry
April 17, 2019 | Jason Fullerton, MacDermid Alpha Electronics SolutionsEstimated reading time: 1 minute
First, can water contamination cause failure? Absolutely! Rainwater contains much higher electrochemically active content than the deionized water used for cleaning PCB assemblies and can lead to corrosion and dendritic growth. If discovered before introduction to the service environment, cleaning may be possible, and the assemblies may be able to be salvaged. Exposure to rainwater in the service environment is a sure path to failure unless the assembly has been ruggedized against such exposures as part of the design.
Second, how do you know if a flux is bad and shouldn’t be used? Flux is a chemical that reacts with oxides that naturally form on metal surfaces. When flux cannot adequately react with the metals that are to be joined, a solder joint does not form properly. Even with fluxes that are properly stored, time can reduce the ability of a flux to perform that intended function.
Third, are there any simple tests for this? A good quantitative test for liquid fluxes is the acid number, and an acid number below the flux’s particular minimum specification is a key indication that a flux should not be used. Otherwise, qualitative testing of a flux’s soldering performance is common to resolve suitability for use after a question. Each form of flux has its own solderability tests that can be performed, but they all boil down to “Does the flux work or not?”
A higher level of defects and reduced soldering performance is to be expected when too-old fluxes are used. Solder joints that form properly are not expected to exhibit reduced reliability. However, a higher number of defects created tends to lead to a higher chance that defective connections escape detection through inspection and functional testing, and that’s not a risk to be taken lightly.
Jason Fullerton is the customer technical support engineer at the Assembly Division of MacDermid Alpha Electronics Solutions.
Suggested Items
Indium Corporation to Present, Exhibit at EPP InnovationsFORUM
03/28/2024 | Indium CorporationIndium Corporation is set to present and exhibit at EPP InnovationsFORUM, one of Europe’s premier single-day electronics manufacturing forums, on April 17 in Leinfelden-Echterdingen, Germany. Topic areas for 2024 will include AI, automation, sustainability, and quality.
Reducing Nitrogen Consumption in Convection Soldering with Rehm Thermal Systems' Patented Mechatronic Curtain
03/28/2024 | Rehm Thermal SystemsCurrent developments indicate a need for larger throughput heights due to the trend towards e-mobility, which in turn increases nitrogen consumption for process inertization. Rehm Thermal Systems responds to this issue with an innovative solution: the mechatronic curtain.
Indium Corporation, Industry Partners to Showcase Products “Live@APEX”
03/26/2024 | Indium CorporationIndium Corporation®, in cooperation with its industry partners, will feature its proven solder solutions live on the show floor throughout IPC APEX Expo from Apr. 9‒11 in Anaheim, Calif., U.S.
ITW EAE Wins New Product Introduction Award for Electrovert® Wave Soldering Machine Deep Wave
03/26/2024 | ITW EAEITW EAE is proud to announce that it has earned a 2024 New Product Introduction (NPI) Award for Electrovert’s Deep Wave option for wave soldering machines. This new, innovative system provides the ability to pump up to a 20 mm wave height.
Mek's Next-Gen AOI Technology Takes Center Stage at IPC APEX EXPO 2024
03/19/2024 | MEKMek is excited to announce its presence at IPC APEX EXPO, North America's largest electronics manufacturing event, in Anaheim, California, from April 6-11, 2024. Attendees are invited to visit Mek at booth #1433 to explore the latest AOI technology offerings.