HDI Design Education: Is Anyone Interested?


Reading time ( words)

I first became aware of high-density interconnection (HDI) design methodology in 1997 when a co-worker of mine came back from a training class that was taught by Happy Holden. “Little Dave” (since our department had two employees named David W.) came back excited to try this new design knowledge on a multilayer board stackup that only used blind and buried vias, with no through-hole vias. His excitement and dedication paid off, as he completed the design with an autorouter exactly as he planned. Through Dave’s success, our department then started to create other designs using HDI stackups that were taught in Happy’s class and our autorouter tool.

I did a few complex designs that fit into the IPC Type III category. One of the more complex designs I attempted could only autoroute up to 98% completion after trying many setup files (with great assistance from “Big Dave”) and our most powerful computer available within our group. I finished the design manually, and the board was fabricated and worked as designed.

About six months later, when we upgraded our department’s autorouter computer, I restored the design from archive, and re-ran the last autorouter configuration file on that 98% completed design. This time, the design was now 100% completely autorouted, and took about a third less time than on the previous “most powerful” computer. This one little re-investigation became the catalyst for my full immersion into HDI design research, reviewing the existing designs and now trying newer autorouting approaches with a variety of more challenging stackups, via spans, and via sizes. Each new redesign attempt created more curiosity to push autorouters and stackup methodologies to their absolute limits.

Over the next few years, any article written on HDI that crossed my path became assimilated into my mental database. I met Mike Fitts lecturing on HDI at a design conference, and I asked him to clarify my repository of HDI re-design questions. When Mike and I met at another design conference, he introduced me to the very person who inspired Little Dave: Happy Holden.

Read the full column here.


Editor's Note: This column originally appeared in the May 2014 issue of The PCB Design Magazine.

I first became aware of high-density interconnection (HDI) design methodology in 1997 when a co-worker of mine came back from a training class that was taught by Happy Holden. “Little Dave” (since our department had two employees named David W.) came back excited to try this new design knowledge on a multilayer board stackup that only used blind and buried vias, with no through-hole vias. His excitement and dedication paid off, as he completed the design with an autorouter exactly as he planned. Through Dave’s success, our department then started to create other designs using HDI stackups that were taught in Happy’s class and our autorouter tool.

I did a few complex designs that fit into the IPC Type III category. One of the more complex designs I attempted could only autoroute up to 98% completion after trying many setup files (with great assistance from “Big Dave”) and our most powerful computer available within our group. I finished the design manually, and the board was fabricated and worked as designed.

About six months later, when we upgraded our department’s autorouter computer, I restored the design from archive, and re-ran the last autorouter configuration file on that 98% completed design. This time, the design was now 100% completely autorouted, and took about a third less time than on the previous “most powerful” computer. This one little re-investigation became the catalyst for my full immersion into HDI design research, reviewing the existing designs and now trying newer autorouting approaches with a variety of more challenging stackups, via spans, and via sizes. Each new redesign attempt created more curiosity to push autorouters and stackup methodologies to their absolute limits.

Over the next few years, any article written on HDI that crossed my path became assimilated into my mental database. I met Mike Fitts lecturing on HDI at a design conference, and I asked him to clarify my repository of HDI re-design questions. When Mike and I met at another design conference, he introduced me to the very person who inspired Little Dave: Happy Holden.

Read the full column here.


Editor's Note: This column originally appeared in the May 2014 issue of The PCB Design Magazine.

Share


Suggested Items

Zuken Teams With Nano Dimension for 3D Printing Design Flow

11/22/2017 | Andy Shaughnessy, PCB Design007
At PCB West, Zuken shared a booth with Nano Dimension. Zuken has been working with Nano Dimension for some time, and adding support for 3D printing and nanotechnology to its design tool platforms. I sat down with Zuken’s Humair Mandavia and Nano Dimension’s Simon Fried to learn more about this alliance, and to find out more about this odd-looking box being demonstrated in Zuken’s booth.

Nine Dot Connects: Good Design Instruction is a True Value-Add

11/09/2017 | Andy Shaughnessy, PCBDesign007
Nine Dot Connects has certainly blazed an interesting trail. The company started out as an Altium reseller, but in less than a decade, Nine Dot Connects has also become a design service bureau and a provider of PCB design instruction, training, and consulting services. I recently interviewed Paul Taubman, technical services director for Nine Dot Connects. We discussed the company’s expansion from VAR to service bureau and content provider, and the changing landscape of PCB design instruction.

AltiumLive Summit—Munich, Germany, Part 2

11/13/2017 | Pete Starkey, I-Connect007
Pete Starkey continues with his review of the AltiumLive PCB Design Summit held recently in Munich, Germany. The second day commenced with a new product launch. “Working together is hard” it read on the screen. Statistics indicated that 33% of new products were late getting to market, of which 28% were late due to insufficient collaboration, and up to 50% of potential revenue could be lost through being late to market. Then the screen read “NEXUS makes it easy!”



Copyright © 2017 I-Connect007. All rights reserved.