-
- News
- Books
Featured Books
- smt007 Magazine
Latest Issues
Current IssueIPC APEX EXPO 2024 Pre-show
This month’s issue devotes its pages to a comprehensive preview of the IPC APEX EXPO 2024 event. Whether your role is technical or business, if you're new-to-the-industry or seasoned veteran, you'll find value throughout this program.
Boost Your Sales
Every part of your business can be evaluated as a process, including your sales funnel. Optimizing your selling process requires a coordinated effort between marketing and sales. In this issue, industry experts in marketing and sales offer their best advice on how to boost your sales efforts.
The Cost of Rework
In this issue, we investigate rework's current state of the art. What are the root causes and how are they resolved? What is the financial impact of rework, and is it possible to eliminate it entirely without sacrificing your yields?
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - smt007 Magazine
Reflow Profiling on the Electrical Reliability of No-Clean Solder Paste Flux Residues
May 5, 2015 | By Eric Bastow, Indium Corp.Estimated reading time: 2 minutes
An estimated 80% of all SMT assembly in the world is performed with a no-clean soldering process, largely due to the predominance of consumer electronics. The continuing trend of increasing miniaturization that dominates modern electronics devices requires no-clean flux residues to be as benign and electrically resistive as possible. Solder pastes with an IPC J-STD-004[1] classification of ROL0 or ROL1 rely heavily on two basic mechanisms to render the flux residue as "no-clean": (1) the encapsulating properties that the rosin provides and (2) the heat activation/decomposition of the chemicals in the flux, commonly known as “activators.” The latter is generally known in the industry, but is rarely taken into consideration for reflow profiling in SMT assembly.
Optimization of a reflow profile often focuses on mitigating defects such as voiding, tombstoning, graping, slumping/bridging, etc. However, little thought is given to the reflow profile’s effect on the electrical reliability of the no-clean flux residue. Because of the wide variation in size and thermal density of SMT components and PCBs, achieving a reflow profile that equally heats the entire assembly can be challenging and often impossible. The temperature under a large component, such as a BGA, is often markedly cooler than a smaller component, such as a passive resistor or capacitor. This paper will discuss an experiment that studied the effect of reflow profiling on the electrical reliability of no-clean flux residues that can be measured using IPC J-STD-004[1] surface insulation resistance (SIR) testing. Both a halogen-free (ROL0) and a halogen-containing (ROL1) Pb-free no-clean solder paste, exposed to various reflow profiles, were used in this study.
Prior work had exposed the impact on SIR values of entrapping a solder paste flux residue under a component body or RF shield. What was unclear in that work is the impact of the reflow profile. Invariably, flux underneath a device does not get exposed to the same heat that an exposed flux does. So performing an experiment that focused solely on the effect of heating seemed pertinent.
Experimental
In this experiment, a total of eight reflow profiles were used for each solder paste; one paste being ROL0 and the other being ROL1. Both solder pastes used are standard commercially available products. All boards were reflowed in a standard convection belt furnace type reflow oven with an air environment. The reflow profiles consisted of four different peak temperatures: 225°C, 235°C, 245°C and 255°C.
For each peak temperature, reflow profiles representing a "ramp to peak" and "soak" profile were created. The purpose of creating both a ramp to peak and a soak profile was to see if and how, not only the peak temperature, but also the “shape” of the profile, has an impact on SIR performance. For the sake of this work, the “soak” is defined as the period during which the PCB is between 200°C and 215°C.
Editor's Note: This article originally appeared in the April issue of SMT Magazine.
Suggested Items
Indium Corporation to Present, Exhibit at EPP InnovationsFORUM
03/28/2024 | Indium CorporationIndium Corporation is set to present and exhibit at EPP InnovationsFORUM, one of Europe’s premier single-day electronics manufacturing forums, on April 17 in Leinfelden-Echterdingen, Germany. Topic areas for 2024 will include AI, automation, sustainability, and quality.
Reducing Nitrogen Consumption in Convection Soldering with Rehm Thermal Systems' Patented Mechatronic Curtain
03/28/2024 | Rehm Thermal SystemsCurrent developments indicate a need for larger throughput heights due to the trend towards e-mobility, which in turn increases nitrogen consumption for process inertization. Rehm Thermal Systems responds to this issue with an innovative solution: the mechatronic curtain.
Indium Corporation, Industry Partners to Showcase Products “Live@APEX”
03/26/2024 | Indium CorporationIndium Corporation®, in cooperation with its industry partners, will feature its proven solder solutions live on the show floor throughout IPC APEX Expo from Apr. 9‒11 in Anaheim, Calif., U.S.
ITW EAE Wins New Product Introduction Award for Electrovert® Wave Soldering Machine Deep Wave
03/26/2024 | ITW EAEITW EAE is proud to announce that it has earned a 2024 New Product Introduction (NPI) Award for Electrovert’s Deep Wave option for wave soldering machines. This new, innovative system provides the ability to pump up to a 20 mm wave height.
Mek's Next-Gen AOI Technology Takes Center Stage at IPC APEX EXPO 2024
03/19/2024 | MEKMek is excited to announce its presence at IPC APEX EXPO, North America's largest electronics manufacturing event, in Anaheim, California, from April 6-11, 2024. Attendees are invited to visit Mek at booth #1433 to explore the latest AOI technology offerings.