-
- News
- Books
Featured Books
- smt007 Magazine
Latest Issues
Current IssueComing to Terms With AI
In this issue, we examine the profound effect artificial intelligence and machine learning are having on manufacturing and business processes. We follow technology, innovation, and money as automation becomes the new key indicator of growth in our industry.
Box Build
One trend is to add box build and final assembly to your product offering. In this issue, we explore the opportunities and risks of adding system assembly to your service portfolio.
IPC APEX EXPO 2024 Pre-show
This month’s issue devotes its pages to a comprehensive preview of the IPC APEX EXPO 2024 event. Whether your role is technical or business, if you're new-to-the-industry or seasoned veteran, you'll find value throughout this program.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - smt007 Magazine
Solder Paste Stencil Design for Optimal QFN Yield and Reliability
April 29, 2015 | Ben Gumpert, Lockheed MartinEstimated reading time: 13 minutes
One assembly was cross-sectioned to evaluate solder joint heights, and the rest were subjected to thermal cycling. The assemblies were continuously electrically monitored during testing to identify when component failures occur. An air-circulating environmental chamber and a thermal cycle of -55°C to 125°C were used. The chamber includes a continuous recording unit for temperature. The ramp rate was set to 4.5°C/min and the dwell time set to 15 minutes.
An electrical continuity monitor was used determine time of failure for individual components. Testing was performed in accordance with IPC-SM-785 standard, with failures identified as short duration, high resistance spikes as described in section 4.3.1 of that guideline. Variations in channel current-loop resistance which exceed the selected threshold resistance were flagged as events, subject to the minimum event duration limit.
Results
Thirteen cards were built with a total of 20 QFN44 and 28 QFN68 packages on each card. Table 2 shows results from cross-section measurements, x-ray inspection, and continuity check. Several points are evident from these results. The first is that ‘open’ defects were present in the QFN68 locations where the least amount of solder reduction was applied. The QFN44 package did not exhibit any of these open defects. Bridging was not a common problem, but seems to have occurred randomly.
Voiding levels were fairly low. Only three locations had total voiding above 25%, and some of these were attributed to ‘bottoming-out’ of the component on the solder mask at B1 sites. It was determined that the solder volume at these sites was low enough such that some parts were resting on the solder mask, which enabled voids to remain in the solder joint instead of making their way out.
One test board was selected for cross-sectioning to evaluate solder joint heights and geometry. Figures 4 and 5 are representative images of the solder joints formed. On components with a larger stand-off height (i.e. taller solder joints), the solder at the toe is slightly concave in shape, while it is convex on the parts with a lower stand-off. This demonstrates that the sizing of the stencil apertures at the perimeter pin locations was not quite compensated enough to achieve consistent fillets at all locations. Solder joint open defects were reworked by hand and were tied in for thermal cycle testing, although the locations were noted for future reference to determine the impact that rework may have on reliability.
Solder joint height for the QFN package is generally defined by the amount of solder applied to the center pad. In this study, the PCBs used had a HASL finish, so they have some volume of solder already present on the center pad. Cross section measurements of the solder joint height (actual height) were compared to the expected values at each location, as seen in Figure 6. This data demonstrates a good trend, and variation seen is attributed to three main variables; pre-existing solder volume from HASL, solder volume applied in-process, and variation of the QFN position in the cross-section (i.e. potential tilt of the package).
To date, the test vehicles have been exposed to 1100+ thermal cycles (-55°C to 125°C), with the profile as shown in Figure 7. There have been only four failures out of the 576 locations thus far. These failures have each been from a QFN68 package of a unique site, but none of these sites were those with greater than 50% solder reduction (the standard lower limit for paste application.)
Page 3 of 4
Suggested Items
Connect the Dots: Designing for Reality—The Pre-Manufacturing Process
05/08/2024 | Matt Stevenson -- Column: Connect the DotsI have been working with Nolan Johnson on a podcast series about designing PCBs for the reality of manufacturing. By sharing lessons learned over a long career in the PCB industry, we hope to shorten learning curves and help designers produce better boards with less hassle and rework. Episode 2 deals with the electronic pre-manufacturing process. Moving from CAD (computer-aided design) to CAM (computer-aided manufacturing) is a key step in PCB manufacturing. CAM turns digital designs into instructions that machines can use to actually build the PCB.
AIM Solder Signs Shinil Fl Ltd. as New Distributor for Korea
05/08/2024 | AIM SolderAIM Solder, a leading global manufacturer of solder assembly materials for the electronics industry, is pleased to announce a new distribution partnership with Shinil Fl Ltd., a prominent supplier of technological solutions in the SMT and semiconductor sectors.
Indium Corporation to Showcase HIA Materials at ECTC
05/07/2024 | Indium CorporationAs an industry leader in innovative materials solutions for semiconductor packaging and assembly, Indium Corporation® will feature its advanced products designed to meet the evolving challenges of heterogeneous integration and assembly (HIA) and fine-pitch system-in-package (SiP) applications at the 74th Electronic Components and Technology Conference (ECTC), May 28‒31, in Denver, Colorado.
Indium Corporation Expert to Present on Pb-Free Solder for Die-Attach in Discrete Power Applications
04/30/2024 | Indium CorporationIndium Corporation Product Manager – Semiconductor Dean Payne will present at the Advanced Packaging for Power Electronics conference, hosted by IMAPS, held May 8-9 in Woburn, Massachusetts, USA.
Taiyo Circuit Automation Installs New DP3500 into Fuba Printed Circuits, Tunisia
04/25/2024 | Taiyo Circuit AutomationTaiyo Circuit Automation is proud to be partnered with Fuba Printed Circuits, Tunisia part of the OneTech Group of companies, a leading printed circuit board manufacturer based out of Bizerte, Tunisia, on their first installation of Taiyo Circuit Automation DP3500 coater.