-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueOpportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
Manufacturing Know-how
For this issue, we asked our expert contributors to share their thoughts on the absolute “must-know” aspects of fab, assembly and test that all designers should understand. In the end, we’re all in this together.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
Alternatives to Simulation
April 23, 2021 | Dan Beeker, NXP SemiconductorsEstimated reading time: 2 minutes
We are living in an age where the demands on electronic product designs are constantly evolving. The IC technology and operating speeds continue to pose significant challenges for teams as they work to develop their products. The increased transistor switching speeds and less forgiving compliance standards make signal integrity and electro-magnetic compliance more difficult to achieve. The status quo seems to have become, “We expect to fail EMC testing.”
What can be done to increase the likelihood of compliance, and proper function? In some cases, the engineering community looks to simulation as a method of evaluating the PCB design. There are certainly a number of powerful tools available, but they are usually expensive and difficult to use properly. These tools are only of value if the transmission lines are not broken. The simulated results often differ from the measured behaviors, forcing model tweaks and lost time. In most cases, you have an incomplete model and inaccurate measurements, which even when reconciled, do not reflect the real behaviors of the design. It is nearly impossible to get good measurements for this purpose. The probes will affect the signal, as does the location in the transmission line where the measurement is taken. Many teams just do not have the bandwidth or expertise to achieve success using this process.
The fundamental issue is that most simulation tools are not capable of evaluating broken transmission lines. (I say “most” because I am not intimately familiar with all of them.) A broken transmission line is a signal or power conductor that is not one dielectric away from ground. If a signal or power conductor is not directly adjacent to a continuous dielectric bounded by a continuous ground conductor, the EM fields do not stay where the design requires. The field will fill the space between the signal conductor and the ground conductor that connects to the power source for the PCB.
The more conductors and dielectrics that are between the signal in question and its ground, the more impact on signal integrity and EMC. There are just not enough nodes in the models. It would require characterizing every change in the transmission line geometry, for not only the signal trace in question, but the other nearby traces and the power supplies for the ICs involved. Once a trace crosses a split in the ground plane, the space involved in the signal transmission expands to include the divergent path of the continuous ground conductor. This increases the time it takes to establish the signal voltage, requiring more wave cycles to achieve the signal levels. Each wave cycle increases crosstalk and possible radiated emissions, which occur at every wavefront. Every other signal crossing the split will also have an expanded space to fill. These signals will then share the space and affect the voltage for each signal. If a power supply is not properly designed, signal integrity is compromised for all the signals using that supply. If a signal is compromised, it affects not only that signal, but other signals in the adjacent areas of the PCB.
To read this entire article, which appeared in the April 2021 issue of Design007 Magazine, click here.
Suggested Items
KIC’s Miles Moreau to Present Profiling Basics and Best Practices at SMTA Wisconsin Chapter PCBA Profile Workshop
01/25/2024 | KICKIC, a renowned pioneer in thermal process and temperature measurement solutions for electronics manufacturing, announces that Miles Moreau, General Manager, will be a featured speaker at the SMTA Wisconsin Chapter In-Person PCBA Profile Workshop.
The Drive Toward UHDI and Substrates
09/20/2023 | I-Connect007 Editorial TeamPanasonic’s Darren Hitchcock spoke with the I-Connect007 Editorial Team on the complexities of moving toward ultra HDI manufacturing. As we learn in this conversation, the number of shifting constraints relative to traditional PCB fabrication is quite large and can sometimes conflict with each other.
Standard Of Excellence: The Products of the Future
09/19/2023 | Anaya Vardya -- Column: Standard of ExcellenceIn my last column, I discussed cutting-edge innovations in printed circuit board technology, focusing on innovative trends in ultra HDI, embedded passives and components, green PCBs, and advanced substrate materials. This month, I’m following up with the products these new PCB technologies are destined for. Why do we need all these new technologies?
Experience ViTrox's State-of-the-Art Offerings at SMTA Guadalajara 2023 Presented by Sales Channel Partner—SMTo Engineering
09/18/2023 | ViTroxViTrox, which aims to be the world’s most trusted technology company, is excited to announce that our trusted Sales Channel Partner (SCP) in Mexico, SMTo Engineering, S.A. de C.V., will be participating in SMTA Guadalajara Expo & Tech Forum. They will be exhibiting in Booth #911 from the 25th to the 26th of October 2023, at the Expo Guadalajara in Jalisco, Mexico.
Intel Unveils Industry-Leading Glass Substrates to Meet Demand for More Powerful Compute
09/18/2023 | IntelIntel announced one of the industry’s first glass substrates for next-generation advanced packaging, planned for the latter part of this decade.