Soldering to Magnet Wires with 50In50Pb Alloy


Reading time ( words)

Posted by Derrick Herron on Monday, October 20, 2014



The Indium Corporation recently had a customer contact us looking for 50In50Pb solder wire.  We manufacture large amounts of this indium-lead material as it is used in numerous applications.  In this case, it was the application that was quite interesting.  I won’t give any customer information, but will say that a report by Hughes Aircraft was brought to our attention.  It can be found online here. The report deals with the bonding of extremely thin copper wire (down to 0.0004” in diameter!) to thicker, more resilient wire.spool_indium.jpg

Through the work done in the above-mentioned paper, it was found that the 50In50Pb formed the strongest bond of the alloys tested and was very limited in its consumption of the copper wire when manufacturing times and temperatures were carefully observed. I was sure to caution our customer that indium and copper will form a brittle intermetallic layer, as my colleague Eric Bastow explains here. However, Eric also points out that this type of solder joint is created every day in applications where it does not cause a problem to the end product. In any application, reliability testing should be done to ensure that the final product exceeds the needs of the environment in which it will be used.  We were curious if more people out there are using indium-lead solder alloys in this type of application.The thicker wire is able to withstand the stresses placed on it in a subsequent encapsulation step, whereas the thin copper wire would break during this step, therefore making the thicker material necessary.  One problem that quickly arose was that if traditional tin-based solders were used to bond these two wires together, they would very rapidly consume the thin copper wire, resulting in an extremely weak interface - if an interface survived at all.  An alternate solder was needed and 50In50Pb was my recommendation.

Please send me a message if you’re doing this type of work or if you’re interested in using our indium-lead alloys for this or any other application. -Derrick

derrick_herron.jpg 

Derrick Herron

Contact Derrick

315-853-4900 x7599

Capture-derrickbuttons.JPG

Share




Suggested Items

Solder Paste Printing and Optimizations for Interconnecting Back Contact Cells

07/26/2022 | Narahari S Pujari and Krithika PM, MacDermid Alpha Electronics Solutions
The interdigitated back contact (IBC) is one of the methods to achieve rear contact solar cell interconnection. The contact and interconnection via rear side theoretically achieve higher efficiency by moving all the front contact grids to the rear side of the device. This results in all interconnection structures being located behind the cells, which brings two main advantages. First, there is no frontside shading of the cell by the interconnection ribbons, thus eliminating the need for trading off series resistance, losses for shading losses when using larger interconnection ribbons. Second, a more homogeneous looking frontside of the solar module enhances the aesthetics.

Optimizing Test Engineering Practices for High-Mix Electronics Manufacturing

08/15/2022 | Mark Laing, Siemens Digital Industries Software
For PCB and assembly manufacturers, test engineering has become a critical factor in enhancing the profitability of new product introductions (NPIs). Given the trend toward high-mix, low-volume production, the journey from design data to an automated PCB testing program must be quicker and more efficient than ever before. In this article, we will discuss how to optimize the efficiency of the test engineering process in accordance with these new market realities.

Time to Get Serious About CMMC Readiness

07/13/2022 | I-Connect007 Editorial Team
Divyash Patel of MX2 Technology is a leading cybersecurity expert who’s sounding the alarm about getting your company into a state of readiness. But he’s not yelling fire in a theater. Whether it’s aligning with DoD’s CMMC, or just ensuring your company’s data and processes are protected, Divyash can see what’s coming. “This is a must-have compliance program,” he says. “It needs to be taken seriously and maintained.”



Copyright © 2022 I-Connect007. All rights reserved.