-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueOpportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
Manufacturing Know-how
For this issue, we asked our expert contributors to share their thoughts on the absolute “must-know” aspects of fab, assembly and test that all designers should understand. In the end, we’re all in this together.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
Designers Notebook: Flex and Rigid-Flex Circuit Design Principles, Part 1
January 27, 2016 | Vern Solberg, ConsultantEstimated reading time: 5 minutes
Flexible circuits represent an advanced approach to total electronics packaging, typically occupying a niche that replaces ordinary printed circuit board assemblies and the hard-wire interface needed to join assemblies. Flex circuits have an advantage over hard-wire interface because they fit only one way, eliminating wire routing errors as well as the time needed for testing and inspection.
Furthermore, flex circuit conductor patterns will maintain uniform electrical characteristics, controlling noise, crosstalk, and impedance. In addition to saving up to 75% on space and weight, flexible circuits improve overall product reliability. In essence, flex circuits furnish unlimited freedom of packaging geometry while retaining the precision, density, and repeatability of printed circuits.
Primary Flexible Circuit Structures
The four basic variations of flexible and rigid-flex circuits are defined as:
- Single-sided flex: The most common type of flexible circuit consists of a conductive layer bonded between two insulating layer materials with SMT lands (when needed) accessible on only one side. The single Cu layer flex is the ideal circuit for dynamic flexing applications.
- Double-sided flex circuit: Where copper foil is bonded on both sides of the base material. Vias connecting sides are punched, drilled or laser ablated and plated prior to chemically etching the circuit pattern. Finally, both sides of the circuit are covered with a dielectric cover-layer or cover-coat.
- Multilayer flex circuits: This type of circuit consists of a number of conductive layers bonded together with dielectric between them. Plated through-holes are used to create the interconnection of the conductive layers. Although referred to as a flex circuit, pliability is considerably lessened with the addition of each layer.
- Rigid-flex circuits: A rigid-flex structure consists of flexible circuit(s), which are then bonded onto or laminated within a rigid dielectric material. Flexible dielectrics provide unlimited conformability between rigid sections of the circuit commonly utilized for component mounting and system interface.
The design guidelines for flexible circuits, although similar to rigid circuits, have distinctive differences that are influenced by specific applications and the intended operating use environments.
Design for Operating Environment
Although the actual use environment may not subject the flex or rigid-flex circuits to excessive conditions, qualifying the end-product often requires thermal cycle testing (typically based on worst-case environments). Consumer and commercial products, for example, are not expected to be exposed to thermal conditions greater than 60°C; however, qualifying products for industrial, automotive and aeronautic applications will require reliable operation at both high and low temperature conditions (+95°C to -55°C).
Base Material Selection
Base material for flexible circuit applications includes both polyester and polyimide films. While polyester-based material may be considered for a number of cost-sensitive consumer applications, polyimide-based materials will continue to be specified for the more demanding environments noted above.
- Polyester films may not be the first choice for a number of applications but it does furnish excellent electrical properties, has relatively low moisture absorption potential and is thermally stable (capable of continuous operation at 105ºC). The material exhibits good to fair dimensional stability, is resistant to most chemicals and is the least expensive of the commonly used dielectric materials.
- Polyimide films have excellent electrical properties, the highest operating temperature capability (>200ºC) and good to excellent dimensional stability. Although the material furnishes excellent chemical resistance (acetone, methyl alcohol, toluene, and trichloroethylene) it has a relatively high moisture absorption rate and is significantly more expensive than polyester films.
Non-reinforced Dielectric
Polyimide remains the favorite alternative for flex and rigid-flex applications because the material is mechanically tough and easily withstands exposure to most harsh operating environments. The designer of the flexible circuit has a fairly wide range of material choices. The films, for example, are furnished in thicknesses that range between a very thin 12 microns (0.0005”) and 125 microns (.005”). For a majority of applications the 50-micron (0.002”) thick material will be specified; however, 25.0-micron (0.001”) thick films are often selected for complex forming conditions or, in dynamic applications, to maximize the circuits’ flexibility. Additionally, copper foil can be furnished on one side or both sides of the dielectric base. The copper foil is commonly laminated onto the surface of the polyimide film using a thin layer of modified acrylic, epoxy, epoxy prepreg, or phenolic butyral. Although copper foil can be furnished on both sides of the flexible base, furnishing copper on only one surface will be significantly less costly than the circuit requiring two-sided copper.
Copper foils are rolled and annealed and furnished in thicknesses of 17.0 microns (~0.0007") and 34.0 microns (~0.0014"). Foils as thin as 5.0 microns (~0.00018”) can also be furnished for semi-additive build-up plating when very high-density circuit routing is required. There are also polyimide films furnished with copper that is cast or deposited directly onto the films surface. These products are generally designated as adhesiveless. The adhesiveless circuits are more pliable and excellent for higher reliability applications, but the supply base is more limited and can be cost prohibitive for many consumer or commercial applications.
Reinforced Dielectric
Material selected for the rigid areas of the circuit is typically reinforced with a woven glass fiber. A key concern is how the material responds to multiple exposures to thermal extremes during the fabrication and assembly process. Material selected should exhibit minimal Z-axis expansion and furnish a higher thermal threshold before decomposition occurs. These factors will contribute to avoiding delamination during the product’s intended life cycle. All materials selected for the rigid-flex circuit will be certified to meet a flammability rating established by Underwriters Laboratory (UL).
Another factor that will influence material selection is the glass transition temperature (Tg), the temperature at which the material begins to relax. For example, the better grades of epoxy-glass laminates have a minimum Tg of 170ºC, while the polyimide-glass composites Tg minimum is extended to 200ºC. In regard to decomposition temperature (Td), epoxy-glass material specified in UL/ANSI FR4/126 and FR-4/129 specifies a minimum of 340ºC.
Note: Polyimide films and glass reinforced and non-reinforced organic base material specifications are detailed further in IPC-4101 and IPC-4102.
Before proceeding with the circuit layout, the designer must consider a number of requirements exclusive to the fabrication of flexible circuits. It’s important to discuss base material sets and alternative fabrication processes with your supplier prior to finalizing the design.
Vern Solberg is an independent technical consultant based in Saratoga, California specializing in SMT and microelectronics design and manufacturing technology. To reach Solberg, click here.
Suggested Items
Trouble in Your Tank: Supporting IC Substrates and Advanced Packaging, Part 5
03/19/2024 | Michael Carano -- Column: Trouble in Your TankDirect metallization systems based on conductive graphite or carbon dispersion are quickly gaining acceptance worldwide. Indeed, the environmental and productivity gains one can achieve with these processes are outstanding. In today’s highly competitive and litigious environment, direct metallization reduces costs associated with compliance, waste treatment, and legal issues related to chemical exposure. What makes these processes leaders in the direct metallization space?
AT&S Shines with Purest Copper on World Recycling Day
03/18/2024 | AT&SThe Styrian microelectronics specialist AT&S is taking World Recycling Day as an opportunity to review the progress that has been made in recent months at its sites around the world in terms of the efficient use of resources:
Matrix to Exhibit at IPC APEX EXPO 2024 in Anaheim, CA
03/05/2024 | MatrixMatrix will be exhibiting at IPC APEX EXPO 2024, to be held on April 9-12, 2024, at the Anaheim Convention Center, Anaheim, CA.
The Chemical Connection: Getting to Know Your Vendor
02/16/2024 | Don Ball -- Column: The Chemical ConnectionAfter working for a capital equipment supplier for almost 50 years, I’ve found that the most important part of getting to know your vendor is good communication among all parties. While contact between fabricators of a constantly changing product line and the designers of those products may occur daily or weekly, conversations between you and your equipment supplier may be years apart. That lengthy gap often means that previous contacts may have been promoted, retired, or moved on to other opportunities. You may have also migrated to a new supplier with whom you have little or no history. In either case, you will be interacting with someone you are unfamiliar with (as they are with you). Therefore, it is essential for both sides to communicate clearly so expectations will align.
EIPC Winter Conference 2024, Day 2: A Closer Look at Global Trends
02/14/2024 | Pete Starkey, I-Connect007The opening session of the second day’s conference proceedings focused on global PCB trends and was introduced and moderated by Dr. Michele Stampanoni, vice president of strategic sales and business development at Cicor Group in Switzerland. He opened the session with Dr. Hayao Nakahara’s knowledgeable and enlightening video presentation on the IC substrates industry.