-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueLevel Up Your Design Skills
This month, our contributors discuss the PCB design classes available at IPC APEX EXPO 2024. As they explain, these courses cover everything from the basics of design through avoiding over-constraining high-speed boards, and so much more!
Opportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
Designers Notebook: Flex and Rigid-Flex Circuit Design Principles, Part 2
February 19, 2016 | Vern Solberg, ConsultantEstimated reading time: 5 minutes
Flexible circuits are commonly developed to replace ordinary printed circuit board assemblies that rely on connectors and hardwire for interconnect. Further, because of the base materials’ durability, flexible circuits have proven to be a more reliable solution for telecommunications, computers, automotive, medical, and aerospace, as well as a wide range of other important applications. The major benefit of the flex circuit over a hardwire interface is the reduction of weight, enhanced reliability and the potential for reduced cost over the life of the end product.
In preparation for developing the flexible or rigid-flex circuit, the PCB designer must gain a reasonably good understanding of the fabrication process and the design guidelines furnished by the potential supplier. Most fabricators welcome the opportunity to discuss the project prior to the actual design process. While they often furnish their companies’ unique capabilities and general design guidance, they will also likely recommend following the industry-established Design Standard for Flexible Printed Boards, IPC-2223 as well. This standard was actually developed by flexible circuit manufacturers, material suppliers and users. The document establishes the specific requirements for the design of flexible printed circuit applications and its forms for accommodating component mounting and interconnecting with associated structures.
Supplier Capability Assessment
Fabrication of flexible and rigid-flex circuits requires unique skills. A broad number of companies have specialized in flexible circuit manufacturing and understand the complexities of processing film-based products. Experience goes a long way. You may already have a business relationship with a reliable supplier for rigid PCBs. But a majority of companies working with traditional rigid organic materials have avoided flex because it is perceived as too complex, too hard to handle, etc.
The first step when researching alternative sources is to look for companies that are already producing quality flexible circuits. Review their technical capabilities and company history. Some specialize in fabricating only one and two metal-layer flex, while others are very comfortable with rigid-flex manufacturing. Some of the issues to consider when selecting the supplier are ease of communication and the physical location of their fabrication facility. The Internet is a good place to begin your search, but you may want to consult with other flexible circuit users for recommendations because they may have already qualified one or more suppliers.
In your search, look for companies that have published feature size capability, material variations, stack-ups and any unique process capabilities they may offer. In regard to feature size capability, features include lines and space recommendations, and via size range. Other physical issues include drilled-hole location tolerance to datum, minimum clearance from copper conductor to mechanically drilled or punched mounting holes, and minimum conductor to edge of board spacing. For rigid-flex applications, the designer will need to establish layer count limitation, ability for furnishing blind/buried vias and sequential lamination capability.
Flex Circuit Outline Planning
Prior to beginning the design phase of the flexible or rigid-flex circuit, the designer will need to develop a model, a non-functional mechanical mock-up of the circuit. The model will allow physical adjustment of the key features, connector to connector, connector to rigid board, rigid board-to-board and so on. Assuming that the designer is furnished with a wiring diagram or schematic of the circuit, conductor density between primary features can be established.
If the circuit includes solder attachment of components and/or connectors, the area(s) needed for mounting and interface must be estimated. Furthermore, it is common practice to furnish some form of reinforcement in the component mounting areas to minimize mechanical stress on the solder interface. Reinforcement may be as simple as an additional layer of the flexible film or non-functional rigid material laminated to the surface under the components mounting zone. Providing reinforcement material under the connector mounting area in particular will minimize stress on the solder interface when subjected to repeated use.
Factors to consider:
- Quantity of signal traces and surface area required across the flexible area
- Line widths required for current-carrying capacity
- Spacing required for voltage isolation
- EMI shielding and impedance control requirement
- Voltage drop limitations
Circuit routing principles
With regard to conductor density, the designer must first establish the general conductor width and space (L/S) in the flexible section between primary features. Although many designers will want to maximize conductor density in this area of the circuit, the actual minimum conductor width will be dictated by three factors: copper thickness, electrical current carrying capacity and the fabricators capability. Purely signal carrying conductors can rely on very narrow copper circuit topography, but when the electrical current reaches 0.5A or greater, a wider circuit path must be established, For example, a reliable flexible circuit supply source recommends that when conductors are carrying 0.5A using ½ oz. (17 micron) thick copper, the conductor width should be around 330 microns (0.013”). When 1 oz. (34 micron) thick copper is specified, the conductor width can be pared down to 200 microns (0.008”). When flexible circuits are designed for higher amperage loads for power distribution, these numbers will grow significantly.
Fabricators recommend that designers avoid unnecessary circuit thickness in the bend zone because it can hinder flexible capabilities. If a portion of the flex circuit needs to be thicker for supporting components or connectors, add a stiffener. Suppliers further note that calculating bend cycles over the projected life of the product is crucial to your design. If a circuit is flexed beyond the limits established, the copper foil may begin to stretch and crack. A general rule of thumb for estimating minimum bend radii is 6x material thickness for single metal circuits and 12x for two metal-layer circuits.
Furthermore, to avoid fatigue of the thin copper foils in the flex zone, conductors should be perpendicular to the bend and maintain a uniform width and spacing. When the conductor’s path must change direction, the designer must avoid sharp 90° turns. Ideally, the conductor paths will be designed with generous radii. Multiple conductor paths routed in parallel should also maintain uniform spacing with progressively larger radii from the center axis. Not all CAD software has the curved, nested conductor routing capability; however, most of the software specifically developed for flexible circuit design will.
Another fatigue potential lies in the transition of the narrow circuit geometry to a larger feature and connector mounting pads and land patterns provided for surface mount components. Reinforcement at the interface can be as simple as supplying a tear-drop-shaped fillet at the transition between the narrow conductor and the wider contact feature. For holes furnished for mounting pin-in-hole components it is good design practice to make the mounting pad area as large as possible. This will maximize adhesion area during the soldering process.
To further reduce adhesion concerns, the designer can provide additional anchor features. Anchors can be as simple as incorporating one or more outward copper spoke-like protrusions placed around the pads perimeter. Then, when the cover-layer film is laminated onto the flexible base it will overlap the reinforcement features and negate the potential adhesion failures.
Vern Solberg is an independent technical consultant based in Saratoga, California specializing in SMT and microelectronics design and manufacturing technology. To reach Solberg, click here.
Suggested Items
AIM to Highlight NC259FPA Ultrafine No Clean Solder Paste at SMTA Wisconsin Expo & Tech Forum
04/18/2024 | AIMAIM Solder, a leading global manufacturer of solder assembly materials for the electronics industry, is pleased to announce its participation in the upcoming SMTA Wisconsin Expo & Tech Forum taking place on May 7 at the Four Points by Sheraton | Milwaukee Airport, in Milwaukee, Wisconsin.
Hentec/RPS Publishes an Essential Guide to Selective Soldering Processing Tech Paper
04/17/2024 | Hentec Industries/RPS AutomationHentec Industries/RPS Automation, a leading manufacturer of selective soldering, lead tinning and solderability test equipment, announces that it has published a technical paper describing the critical process parameters that need to be optimized to ensure optimal results and guarantee the utmost in end-product quality.
Empowering Electronics Assembly: Introducing ALPHA Innolot MXE Alloy
04/16/2024 | MacDermid Alpha Electronics SolutionsIn the rapidly evolving electronics industry, where innovation drives progress, MacDermid Alpha Electronics Solutions is committed to setting a new standard. Today, we are pleased to introduce ALPHA Innolot MXE, a revolutionary alloy meticulously engineered to address the critical needs of enhanced reliability and performance in modern electronic assemblies.
New Book on Low-temperature Soldering Now Available
04/17/2024 | I-Connect007I-Connect007 is pleased to announce that The Printed Circuit Assembler’s Guide to… Low-temperature Soldering, Vol. 2, by subject matter experts at MacDermid Alpha Electronics Solutions, is now available for download.
Inkjet Solder Mask ‘Has Arrived’
04/10/2024 | Pete Starkey, I-Connect007I was delighted to be invited to attend an interactive webinar entitled “Solder Mask Coating Made Easy with Additive Manufacturing,” hosted by SUSS MicroTec Netherlands in Eindhoven. The webinar was introduced and moderated by André Bodegom, managing director at Adeon Technologies, and the speakers were Mariana Van Dam, senior product manager PCB imaging solutions at AGFA in Belgium; Ashley Steers, sales manager at Electra Polymers in the UK; and Dr. Luca Gautero, product manager at SUSS MicroTec Netherlands.