-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueOpportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
Manufacturing Know-how
For this issue, we asked our expert contributors to share their thoughts on the absolute “must-know” aspects of fab, assembly and test that all designers should understand. In the end, we’re all in this together.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
EDA Tools: Automation vs. Control
June 13, 2016 | Andy Shaughnessy, PCBDesign007Estimated reading time: 2 minutes
Stephen V. Chavez, CID+, has been a senior-level PCB designer for almost 20 years. He is currently the lead PCB designer for the Electronic Systems Center division of UTC Aerospace Systems (UTAS).
Stephen stays pretty busy. He’s the vice president of his local IPC Designers Council chapter in Phoenix, and a Designers Council Executive Board member at large, and he is recognized as a Subject Matter Expert by IPC. He often speaks at the Design Forum at IPC APEX EXPO. At this year’s Design Forum, “Steph” spoke about the importance of taking charge of your PCB design education and networking.
I caught up with Stephen and asked for his thoughts on the EDA tools of today, and whether he’d prefer to have more control vs. more automation.
Andy Shaughnessy: You’ve been a designer for a few years. In general, what do you think of today’s design automation tools?
Stephen Chavez: It’s true that I’ve been designer for many years now and have used a variety of tool sets. In my experience, I find today’s automation tools extremely useful and when the opportunity presents itself to use these type tools, they can assist greatly in the overall success of a project. Today’s tools have gotten very powerful. They range from very simple to use, to very complex in nature. In my opinion as a designer, I strongly feel that when a designer progresses in his/her career and perfects his/her craft, if and when the opportunity exist, they should take advantage of these new automated tools to design a more quality product, shorten the overall design cycle, and positively affect the overall project budget. With today’s designs getting more and more complex, there are instances where the only way to complete a task is to take advantages of these automation tools. Taking advantages of the horse power within these automation tools in today’s design world is key and I feel these tools should be evaluated to see how they can benefit you and your employer by positively impact your effectiveness as a designer and ultimately improve your company’s success.
Shaughnessy: For your day-to-day design work, would you rather see more automation in your tools, or have more manual control? Is it just a matter of having the correct mix?
Chavez: For me, I’d rather have more automation in my tools. Being able to do tasks faster, work more efficiently, and producing better quality designs allows me more time to evaluate multiple options for better results and of course shortens my design cycle. With that said, having the correct mix is important too. I feel each designer has to figure out what works best for him/her and within his company. In the end, it’s not the tool that makes the difference… It’s the designer!
Shaughnessy: In what areas of design do you usually favor more automation?
Chavez: For me, I’d have to say the areas of design I favor more automation are as follows: constraint input/edits/updating, autorouting, generating outputs, documentation, DFM checking (Valor), design re-use and library part creation (symbols and cells). These are areas I feel where taking advantage of today’s automated tools is a must and can be a game changer.
To read this entire article, which appeared in the May 2016 issue of The PCB Design Magazine, click here.
Suggested Items
KIC’s Miles Moreau to Present Profiling Basics and Best Practices at SMTA Wisconsin Chapter PCBA Profile Workshop
01/25/2024 | KICKIC, a renowned pioneer in thermal process and temperature measurement solutions for electronics manufacturing, announces that Miles Moreau, General Manager, will be a featured speaker at the SMTA Wisconsin Chapter In-Person PCBA Profile Workshop.
The Drive Toward UHDI and Substrates
09/20/2023 | I-Connect007 Editorial TeamPanasonic’s Darren Hitchcock spoke with the I-Connect007 Editorial Team on the complexities of moving toward ultra HDI manufacturing. As we learn in this conversation, the number of shifting constraints relative to traditional PCB fabrication is quite large and can sometimes conflict with each other.
Standard Of Excellence: The Products of the Future
09/19/2023 | Anaya Vardya -- Column: Standard of ExcellenceIn my last column, I discussed cutting-edge innovations in printed circuit board technology, focusing on innovative trends in ultra HDI, embedded passives and components, green PCBs, and advanced substrate materials. This month, I’m following up with the products these new PCB technologies are destined for. Why do we need all these new technologies?
Experience ViTrox's State-of-the-Art Offerings at SMTA Guadalajara 2023 Presented by Sales Channel Partner—SMTo Engineering
09/18/2023 | ViTroxViTrox, which aims to be the world’s most trusted technology company, is excited to announce that our trusted Sales Channel Partner (SCP) in Mexico, SMTo Engineering, S.A. de C.V., will be participating in SMTA Guadalajara Expo & Tech Forum. They will be exhibiting in Booth #911 from the 25th to the 26th of October 2023, at the Expo Guadalajara in Jalisco, Mexico.
Intel Unveils Industry-Leading Glass Substrates to Meet Demand for More Powerful Compute
09/18/2023 | IntelIntel announced one of the industry’s first glass substrates for next-generation advanced packaging, planned for the latter part of this decade.